 |
 |
FORMULATE YOUR SUCCESS
WITH
FORMULATED POLYMERS
|
|
|
|
 |
| News & Events :
|
|
| |
| FORMPOLY® Polyamide – 66 (Nylon 66) |
Over the years, FPL has established 400 grades in 10 engineering polymers mostly specialising in niche
compounds. FPL has approvals from various OEMs serving large sectors of industries with product reach
internationally.
FPL facilities are certifed to ISO 9001:ISO/TS 16949 and ISO 14001 quality systems. FPL combining a
strong technology base with application expertise, design and manufacture Engineering Plastic from
relatively inexpensive compounds to sophisticated high end engineering plastic compounds.
|
|
| GRADE |
DESCRIPTION |
CHARACTERISTICS |
APPLICATIONS |
|
| Unfilled Grades |
| N66GP30 |
General Purpose moulding |
Heat stabilised, nucleated for fast molding cycle with excellent mold release tolerating wide temperature processing |
Terminals, Connectors, Luck nut Fasteners, Pulleys, Motor insulation parts, Fuse Box, Plugs, Spectacle Frames, Switch parts, Knobs of MCB |
| Extensions |
Prefix |
Suffix |
Description |
Special Characteristics |
| |
T |
Increased toughness |
Improved impact |
| |
ST |
Higher toughness |
Higher impact load bearing |
| |
M |
Extended UV stability |
Moderate anti aging to UV radiation |
| |
U |
With UL certification |
Available with UL yellow card |
| S |
|
Special formulation |
Customer specific |
|
| Glass Fiber Reinforced Grades |
| N66GF10 N66GF15 N66GF33 N66GF35 N66GF43 |
10% Glass Fiber 15% Glass Fiber 33% Glass Fiber 35% Glass Fiber 43% Glass Fiber |
Offers high mechanical / thermal properties. Offers reduced shrinkage. Shows excellent surface finish. Combination of higher heat performance with good rigidity |
Radiator fans / Shroud, Terminal block, Switch housing, Chair base, Gears, Cams, Housing, Holder, Rollers, Propeller, Washer, High Pressure seals, Dip stick, Reservoir caps, Armature core, Bobbins, Railway liner |
| Extensions |
Prefix |
Suffix |
Description |
Special Characteristics |
| |
T |
Increased toughness |
Improved impact |
| |
HSL |
Heat Stabilised, Lubricated |
For high heat applications |
| |
HSLR |
Heat stable with glycol resistant |
For radiator applications |
| |
LT |
Lubricated, increased toughness / higher tensile |
Easy moulding with increased tensile and toughness; good surface finish |
| |
EP |
Easy paint |
Better paint adhesion |
| |
M |
Extended UV stability |
Moderate anti aging to UV radiation |
| S |
|
Special formulation |
Customer specific |
|
| Flame Retardant Grades |
| N66GP30FR |
Unfilled FR meets UL94 V0 |
Moderate strength, anti dripping |
Selected grades are available with UL certification |
| N66GF15FR N66GF25FR |
Glass Fiber + FR meets UL94 V0 |
Combination of good mechanical / thermal properties. FR from 0.8mm thick parts |
Relay parts, carbon brush holder , Coil former, Bobbin, Switch parts, Terminal Block, Printed Circuit Board frame, Connectors, |
| N66MF25FR |
Mineral + FR |
Meets UL 94 V0 rating; moderate strength. |
| Extensions |
Prefix |
Suffix |
Description |
Special Characteristics |
| |
FH |
Halogen free system |
Meets REACH / RoHs compliance |
| |
P |
Phosphorus based system |
For selected applications of low density |
| |
U |
UL certified |
With UL 94 yellow card |
| S |
|
Special formulation |
Customer specific |
|
| Self Lubrication Grades |
| N66MS30 |
MoS2 filled |
Dry lubrication for anti-friction & improved wear resistance. Low co-efficient of friction for moving parts |
Parts which requires self lubrication and cannot be greased in the applications like Gears, Sleeves, Actuators, Clutches |
| N66GE30 |
Graphite filled |
| N66PTF30 |
PTFE filled |
|
| Specialty Grades – Heat Stabilised, Mineral Reinforced, High Impact, UV stable |
| N66HS30 |
Heat Stabilized |
Good Heat stabilised for prolonged high temperature exposure; brown in colour |
Where parts are exposed to hot air / hot oil applications including hot diesel; Bearing Retainer Ring |
| N66MF15 N66MF25 N66MF30 |
15% Mineral
25% Mineral
30% Mineral |
Heat stabilised mineral reinforced Offers moderate strength Low warping |
Wheel cover, Lamp housings, engine shroud Switch housing, Lids, Grills, Engine hood, Instrument housing |
| N66MG40 |
40% Mineral + Glass Fiber |
Moderate strength with good finish. Easy molding |
Wheel Cover ,MCB housings, Engine Hood, Heater grills |
| N66ST35 N66ST80 |
Super Tough high impact grade |
High Impact Strength, Low density. No break at room temp and high impact at -40'C |
Parts involving repeated impact and also for applications which needs to perform at low temperature |
| N66GP30UV |
UV stable unfilled |
For outdoor applications meeting SAE J 1883 / J 1963 standards. Highly stable formulations |
Outdoor application where direct sun light is encountered like door handle of automobiles, Marine parts, Auto interior parts |
| N66GF30UV |
30% GF with UV stability |
|
| |
In addition to above FPL have many other formulations for many end-use applications. FPL also has many
Application Specific grades and alloys / blends for many Specific requirements. May be some of them may
suit your requirements also. Call on us to know more about us and about our FORMPOLY® product range.
FPL offers the end-user industry, the designer and the processor with a wide range of plastic compounds
to meet every application.
FPL’s full range of service includes development assistance, custom formulations, product and application
guidance. |
| |
|
All FORMPOLY® products are in pellet form and offered in standard 25 Kg and 500 Kg moisture proof bags. MOQ for Produced for stock grades are based on packing size mentioned here, and for produced against order depends on the colour, polymer and the same provided by your nearest supply chain executive. |
| |
|
FORMPOLY® grades are designed and manufactured carefully to achieve easy flow, permit thin section moulding , fast solidification and best release property in case of injection moulding and uniform flow with excellent dimension stability in case of extrusion. FPL grades are process stabilised for easy processing under wide temperature range.
More details of processing can be seen in compact disc provided for each grade. Ask for assistance to nearest technical services staff to establish the processing and in case of difficulties.
|
| |
|
| MATERIAL SAFETY DATA SHEET |
|
MSDS for FORMPOLY® polymer groups are available. Ask for a copy or can be located in compact disc of
FORMPOLY® Product Data Sheet. |
|
|
| |
|
|
|
| Reach @ |
|
|
|
 |
| Network |
57-60, SIDCO Industrial Estate,
Thirumazhisai, Chennai-600 124,
INDIA. |
 |
144/1 Patilvasti, Jambulkar Nagar
Hinjgwadi,
Pune-411 057,
INDIA. |
|
Rao Market,
Plot No. 5, 2nd Gali,
Sarhaul Village,
Sector 18,
Gurgaon-122 001,
INDIA. |
|
No.67/49,
4th Cross, Begur Road, Bommanhalli,
Bengaluru-560 068,
INDIA. |
|
|
|
© Copyright 2011 - Formulated Polymers Limited, All Rights Reserved. |
|
|
|
